Oracle SPARC Enterprise M3000 Reference Manual Download Page 401

Page: 401 / 552

showemailreport(8)

System Administration

383

NAME

showemailreport - display the email report configuration data

SYNOPSIS

showemailreport

[

-v

]

showemailreport

-h

DESCRIPTION

showemailreport

(8) displays the email reporting configuration data. When used

without options, it displays current email report configuration data.

Privileges

You must have

platadm

platop

fieldeng

privileges to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

EXTENDED

DESCRIPTION

Emailreport information includes whether Emailreporting is enabled. If enabled, it
also includes the list of addresses.

EXAMPLES

EXAMPLE 1

Displaying Emailreport configuration

EXIT STATUS

The following exit values are returned:

SEE ALSO

setemailreport

(8)

-h

Displays usage statement.

When used with other options or operands, an error occurs.

-v

Specifies verbose output.

XSCF>

showemailreport

EMail Reporting: enabled

Email Recipient Address: [email protected], [email protected]

Successful completion.

An error occurred.

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands