Oracle SPARC Enterprise M3000 Reference Manual Download Page 296 | Manualshive

Page: 296 / 552

background image

setsnmp(8)

282

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised August 2009

addv3traphost

Enables the SNMP agent to send SNMPv3 traps or informs to the
desired host. An authentication protocol must be chosen. Valid
protocols are:

MD5

= Uses the MD5 algorithm for authentication

SHA

= Uses SHA (Secure Hash Algorithm) for authentication

The encryption protocol used in all communication is DES (Data
Encryption Standard). If the password option is not used, you
will be prompted for a password. Passwords will be read but not
echoed to the screen.

addv3traphost

takes the following

options:

-a

authentication-password

Sets the authentication password. Must be equal to or greater than 8
characters.

-e

encryption-password

Sets the encryption password.

-i

Asks for an acknowledgment from the receiving host.

-n

engine_id

Sets identifier of the local agent sending the trap. It can be the
engine ID of the local SNMP agent or not but it must match the
engine ID expected by the receiving host. Must start with “

0x

” and

should consist of even hexadecimal characters or you will get an
error.

-p

trap-port

ID of the trap port. Default value is 162.

-r

authentication-protocol

Sets the authentication protocol.

traphost

Host name or IP address of the trap host.

-u

username

Specifies a valid user name.

«
...
294
295
296
297
298
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

Flex System x240 Compute Node

Brand: IBM Pages: 28

Brand: Oki Pages: 2

Brand: IBM Pages: 128

Brand: IBM Pages: 44

x3100 M5 Type 5457

Brand: IBM Pages: 688

Brand: Sun Microsystems Pages: 4

Brand: Ubiquiti Pages: 28

Brand: NMS Communications Pages: 22

callpilot 1002rp

Brand: Avaya Pages: 150

Brand: Seyeon Pages: 10

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

System x3300 M4

Brand: IBM Pages: 470

System x iDataPlex dx360

Brand: IBM Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands