Oracle SPARC Enterprise M3000 Reference Manual Download Page 447 | Manualshive

Page: 447 / 552

background image

showlogs(8)

System Administration

429

Date

:

Log collection date and time (month day hour:minute:second
time-zone year)

The displayed time is the local time.

Code

:

Error code

Data is displayed in 16-byte format.

Occurred

:

Date (Month Day Hour: Minute: Second TimeZone Year) when
an error occurred.

This date is displayed as the local time.

Status

:

Error status

One of the following states is displayed:

Warning

Partial degradation of the unit or warning
about the FRU

Alarm

FRU failure or error

Information

Notification

Notice

System state notification

FRU

:

Suspected faulty unit

The suspected faulty units that are displayed and delimited by a
"

,

" (comma) are the units most likely and second most likely to

be faulty. If there are three suspected faulty units, an "

*

" is

displayed next to the unit third most likely to be faulty. Display
of more than two suspected faulty units depends on whether
more than two suspected faulty units are detected.

Msg

:

Error description

Diagnostic

Code

:

Detailed error code

The displayed code is a hexadecimal number.

UUID

:

Abbreviation for Universal Unique Identifier

This is a globally unique ID that is a 32-digit hexadecimal
number.

«
...
445
446
447
448
449
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: Lantronix Pages: 10

Brand: Lantronix Pages: 17

Brand: Lantronix Pages: 109

Brand: Lantronix Pages: 24

Brand: Lantronix Pages: 29

Brand: Lantronix Pages: 2

Express5800/R310e-E4

Brand: NEC Pages: 86

Express5800/R120h-1E

Brand: NEC Pages: 52

Brand: NEC Pages: 128

Server 3100 series

Brand: Digital Equipment Pages: 71

Brand: RackSolutions Pages: 8

DiskStation Series

Brand: Synology Pages: 6

Brand: DNP Pages: 2

Brand: ASROCK Rack Pages: 51

TS-U100 - NAS Server - USB

Brand: TRENDnet Pages: 47

Brand: Bodet Pages: 13

Force10 MXL Blade

Brand: Dell Pages: 2

FusionServer RH2288H V3

Brand: Huawei Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands