Oracle SPARC Enterprise M3000 Reference Manual Download Page 287 | Manualshive

Page: 287 / 552

background image

setshutdowndelay(8)

System Administration

273

NAME

setshutdowndelay - set the shutdown wait time at power interruption of the
uninterruptible power supply (UPS)

SYNOPSIS

setshutdowndelay

-s

time

setshutdowndelay

-h

DESCRIPTION

The

setshutdowndelay

(8) command sets the wait time before the start of system

shutdown for when power interruption occurs in a system connected to the UPS.

The start of system shutdown can be delayed until the specified time. When power
recovery is reported from the UPS within the specified time, shutdown will not
occur.

Privileges

You must have

platadm

or

fieldeng

privileges to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

EXTENDED

DESCRIPTION

The currently set wait time can be displayed by using the

showshutdowndelay

(8)

command.

EXAMPLES

EXAMPLE 1

Sets 600 seconds as the wait time before the start of shutdown.

EXIT STATUS

The following exit values are returned:

SEE ALSO

showshutdowndelay

(8)

-h

Displays usage statement. When used with other options or
operands, an error occurs.

-s

time

Specifies the wait time before the start of shutdown in units of
seconds. Specify an integer number ranging from

0

to

9999

for

time

. The default value is 10 seconds.

XSCF>

setshutdowndelay -s 600

0

Successful completion.

>0

An error occurred.

«
...
285
286
287
288
289
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: Lantronix Pages: 6

Brand: Lantronix Pages: 27

e Server iSeries 825

Brand: IBM Pages: 52

UniServer R6900 G5

Brand: H3C Pages: 17

Brand: Sun Microsystems Pages: 90

Brand: Thecus Pages: 130

Crestron 908012

Brand: SIERRA VIDEO SYSTEMS Pages: 32

TeraStation TS-RXL/R5

Brand: Buffalo Pages: 91

Brand: LOVATO ELECTRIC Pages: 5

Brand: Huawei Pages: 39

Brand: Huawei Pages: 188

5288 V3 V100R003

Brand: Huawei Pages: 297

Brand: Huawei Pages: 2

Alcatel-Lucent OXO Connect Compact

Brand: Nokia Pages: 216

VGF-HS1 - Vaio Home Server

Brand: Sony Pages: 2

Brand: Sony Pages: 28

Brand: Sony Pages: 313

HES-V1000 - Home Entertainment Server

Brand: Sony Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands