Oracle SPARC Enterprise M3000 Reference Manual Download Page 339

Page: 339 / 552

showarchiving(8)

System Administration

323

NAME

showarchiving - display log archiving configuration and status

SYNOPSIS

showarchiving

[

-e

] [

-v

]

showarchiving

-h

DESCRIPTION

showarchiving

(8) displays the status and configuration information for log

archiving on the Service Processor.

Privileges

You must have

platadm

platop

fieldeng

privileges to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

EXTENDED

DESCRIPTION

If the

-e

option is not specified,

showarchiving

displays the following

information:

1. A list of archiving configuration data:

-e

Displays information about the last ten archiving errors.

-h

Displays usage statement.

When used with other options or operands, an error occurs.

-v

Specifies verbose output.

Archiving state

Log archiving is enabled or disabled.

Archive host

The host on which the logs are archived. Initial
value is

Not configured

. Possible values are

a host name or IPv4 address.

Archive directory

The directory on the archive host where the
archives are stored. Initial value is

Not

configured

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands