Oracle SPARC Enterprise M3000 Reference Manual Download Page 538

Page: 538 / 552

unlockmaintenance(8)

516

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised September 2008

EXAMPLE 2

Unlocks the maintenance lock status. Automatically answers "

" to all

prompts.

EXAMPLE 3

Unlocks the maintenance lock status. Suppresses prompts, and automatically
answers "

" to all prompts.

EXIT STATUS

The following exit values are returned:

SEE ALSO

addfru

(8)

deletefru

(8)

replacefru

(8)

XSCF>

unlockmaintenance -y

This command unlocks the maintenance lock which prevents the multiple

execution of maintenance commands.

*Never* use this command, except when the lock state remains by some reason.

Careless execution of this command causes serious situation because it

interrupts the running command and XSCF might not be able to recognize the

parts.

Continue? [y|n] :y

XSCF>

unlockmaintenance -q -y

XSCF>

Successful completion.

An error occurred.

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands