Oracle SPARC Enterprise M3000 Reference Manual Download | Manualshive

Page: 215 / 552

background image

setdualpowerfeed(8)

System Administration

201

NAME

setdualpowerfeed - set dual power feed mode

SYNOPSIS

setdualpowerfeed

-s

key

setdualpowerfeed

-h

DESCRIPTION

The

setdualpowerfeed

(8) command specifies dual power feed mode in the

system.

Note –

The ability to enable and disable dual power feed is available on M3000/

M4000/M5000 servers only. However, dual power feed mode cannot be used with
100V power on M4000/M5000 servers. When the optional power cabinet for dual
power feed is connected on M8000/M9000 servers, it automatically configures dual
power feed mode. For details about the setting of dual power feed, see the

Installation Guide

for your server.

To enable the dual power feed mode, you need to execute the

rebootxscf

(8)

command or turn off and on the input power.

To disable the dual power feed mode, you need to turn off and on the input power.

Privileges

You must have

platadm

or

fieldeng

privileges to run this command.

Refer to

setprivileges

(8) for more information.

OPTIONS

The following options are supported:

EXTENDED

DESCRIPTION

The state of the current dual power feed mode can be checked by using the

showdualpowerfeed

(8) command.

EXAMPLES

EXAMPLE 1

Disables dual power feed mode in the system. Before rebooting the system, a
message is displayed.

-h

Displays usage statement. When used with other options or
operands, an error occurs.

-s

key

Sets dual power feed mode in the system. Either of the following
can be specified for

key

:

enable

Enables the dual power feed mode.

disable

Disables dual power feed mode.

XSCF>

setdualpowerfeed -s disable

enable -> disable

NOTE: Dual power feed will be disabled the next time the platform is powered
on.

«
...
213
214
215
216
217
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Power 720 Express 8202-E4B

Brand: IBM Pages: 64

Brand: IBM Pages: 148

Brand: IBM Pages: 36

Brand: IBM Pages: 834

NEAX2000 IVS Series

Brand: NEC Pages: 160

Brand: Jung Pages: 16

H SERIES RS/6000

Brand: IBM Pages: 424

Brand: DNP Pages: 93

Brand: Eneo Pages: 94

Brand: Antrica Pages: 68

Brand: ICP DAS USA Pages: 59

60 Business Phone

Brand: ESI Pages: 2

Brand: CNET Pages: 14

Brand: XtendLan Pages: 24

Brand: Habey Pages: 3

Brand: Black Box Pages: 2

Brand: Black Box Pages: 2

Brand: Black Box Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands