Oracle SPARC Enterprise M3000 Reference Manual Download Page 258 | Manualshive

Page: 258 / 552

background image

setnetwork(8)

244

SPARC Enterprise Mx000 Servers XSCF Reference Manual • Last Revised April 2010

■

After you set the network interface, if you disable that network interface and
execute the

applynetwork

(8) command, the setting data of IP address and

netmask will be stored in XSCF. When you enable the network interface, the
setting of IP address and netmask will be used.

■

In the following cases, the

setnetwork

(8) command results in an error:

■

When specified the same IP address as an existing IP address

■

When specified a subnet which is the same with DSCP

■

When specified the same subnets in ISN and in other network interface

■

When specified the

-c

or

-r

option and ISN together

■

When the netmask that specified by using the

-m

addr

option does not

correspond to either of the cases below:

Only the most significant bit is 1

Repeated 1 from the most significant bit

■

If M3000/M4000/M5000 servers corresponds to the cases below, the

applynetwork

(8) command results in an error.

■

If xscf#0-lan#0 and xscf#0-lan#1 are in the down status

■

If xscf#0-lan#0 and xscf#0-lan#1 are in the up status and the same subnets
have been set

■

On M8000/M9000 servers, if xscf#0-lan#0, xscf#1-lan#0, xscf#0-lan#1, and xscf#1-
lan#1 are all in the down status, the

applynetwork

(8) command results in an

error.

■

On M8000/M9000 servers, if the network interface which is in the up status has
the following settings, the

applynetwork

(8) command results in an error.

■

If the subnet of xscf#0-lan#0, xscf#1-lan#0, and the takeover IP address lan#0
are different

■

If the subnet of xscf#0-lan#1, xscf#1-lan#1, and the takeover IP address lan#1
are different

■

If the subnet of ISN is different

■

If the subnet of xscf#0-lan#0 and xscf#0-lan#1 are the same

■

If the subnet of xscf#1-lan#0 and xscf#1-lan#1 are the same

■

In case you specified the IP address and the netmask to the interfaces other than
ISN and when the ISN is not configured, the following default value will be set:

■

xscf#0-if

:

IP address:

192.168.1.1

Netmask:

255.255.255.0

■

xscf#1-if

:

IP address:

192.168.1.2

Netmask:

255.255.255.0

■

The

shownetwork

(8) command can display current information on a network

interface configured for XSCF.

«
...
256
257
258
259
260
...
»

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARC Enterprise M3000

Brand: AIC Pages: 112

Brand: Axis Pages: 66

SuperServer E300-9C

Brand: Supermicro Pages: 113

System X Series

Brand: IBM Pages: 6

TVS- 72XU Series

Brand: QNAP Pages: 56

Brand: Allnet Pages: 148

Brand: BITMAIN Pages: 16

Brand: Planet Pages: 24

Brand: AMX Pages: 2

SafeNet ProtectServer Network HSM 5.9

Brand: Thales Pages: 37

Brand: Inspur Pages: 2

Brand: Inspur Pages: 92

Brand: Inspur Pages: 115

Brand: Inspur Pages: 142

Brand: Gigabyte Pages: 100

TCP/IP Print Server

Brand: Galileo Pages: 9

Brand: IBM Pages: 622

Brand: Sagem Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands