Oracle SPARC Enterprise M3000 Reference Manual Download Page 449

Page: 449 / 552

showlogs(8)

System Administration

431

■

Event log

Default

Date

Log collection date and time (month day hour:minute:second
time-zone year)

The displayed time is the local time.

Event

Power status

One of the following states is displayed:

Domain Power On

The domain power is on.

Domain Power Off

The domain power is off.

System Power On

The system power is on.

System Power Off

The system power is off.

SCF Reset

XSCF is in the reset state.

Domain Reset

The domain is in the reset state.

XIR

The domain CPU is in the reset
state.

Cause

Factor that caused this Status

One of the following factors is displayed:

Self Reset

Power On

System Reset

Panel

Scheduled

RCI

Pow.Fail/Recov.

Operator

SW Request

Alarm

Fatal

Panic

DID

Domain ID

domain_id

can be

–

depending on the system configuration.

Switch

Status of the mode switch of the operator panel

One of the following states are displayed:

Locked

Normal operation mode

Service

Service mode

Date Message

Mar 30 17:45:31 JST 2005 System power on

Summary of Contents for SPARC Enterprise M3000









































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands

Oracle SPARC Enterprise M3000, Reference Manual

Search results

Summary of Contents for SPARC Enterprise M3000

Reviews:

Related manuals for SPARC Enterprise M3000

Brands by name

Popular brands