52
Flexible Mode
Section 4-6
When the Option Board is unable to execute one of the write parameter
instructions, it adds an error value and the failed element index to the result
data. Changing Option Board parameter elements 915.9 - 915.12 for exam-
ple:
Has the following result:
Note that the error number is followed by the element number where the
change instruction failed. I.e. The changes to Option Board parameter ele-
ments 915.9 and 915.10 were carried out successfully. The attempt to change
915.11 failed and changes to subsequent elements (915.12) were not carried
out.
4-6
Flexible Mode
The Flexible device profile lets you operate the Inverter using the Modbus
registers directly. Parameters P160 - P169 and P170 - P179 can be used to
map Modbus registers into the cyclically exchanged process areas. User
parameters P160 - P169 configure the output process area mappings where
parameters P170 - P179 configure the input process area mappings.
4-6-1
Typical Configuration
Step 1
Configure the Option Board and Network as explained in sections
3-1 Config-
uring the Option Board
and
3-2 Configuring the Network
, but limit the follow-
ing choices:
Table 71 DP-V1 Class 2 Write-Parameter Change Instruction Bad Parameter
Word offset
DP Hea
d
er
MSAC2
_W
rite
+0
+1
+2
+3
+4
Description
Request Header
Parameter Address
REF
RT
DO
N
PA
CA
PNU
IND
Message
data
[hex]
0B
02
01
01
10
04
0393
0009
[dec]
11
2
1
1
16
4
915
9
Request reference
Parameter change instruction
Start element 915.9
1
st
Inverter attached to Option Board
4 elements
1 parameter address and value to follow
Addressing values
+5
+6
+7
+8
+9
DP T
railer
Value data
FMT
CV
DATA
42
04
0000
0000
0000
0000
66
4
0
0
0
0
DATA format = WORDs
915.9
915.10
915.11
915.12
4 values
Value data
Table 72 DP-V1 Class 2 Read-Result of Change Instruction on Bad Parameter
Word offset
DP
H
ea
d
er
MSAC2
_Rea
d
+0
+1
+2
+3
+4
D
P
T
rai
le
r
Description
Request Header
Values
REF RT DO
N
FMT CV
DATA
DATA
Message
data
[hex]
0B
82
01
01
44
02
0003
000B
[dec]
11
130
1
1
68
2
3
11
Request reference
Failed
Parameter change error
Error no: Faulty
1
st
Inverter attached to Option Board
2 values
1 error value to follow
DATA format = Error no
I111E-EN-02+3G3AX-MX2-RX-PRT+OperManual.book Seite 52 Donnerstag, 8. September 2011 11:53 11
Summary of Contents for 3G3AX-MX2-PRT-E
