manualshive.com logo in svg

Oki MSM66591, User Manual

Share
Download
Oki MSM66591 User Manual Download Page 278

15-13

15

MSM66591/ML66592 User's Manual

Chapter 15   Serial Port Functions

[7]

SCI0 Status Register 1 (S0STAT1)

If the SR0EXP bit of SR0CON is set to "1" (4-stage buffer mode), the 6-bit S0STAT1
register stores the status (normal/abnormal) of the serial transfer when a serial port
receive operation is completed.

During the 4-stage buffer mode, if there is an error in the receive data transferred to
S0BUF1, the lower 3 bits of S0STAT1 (bits 1–3) are updated when reception of that
data is complete; if there is an error in the receive data transferred to S0BUF2, the
upper 3 bits of S0STAT1 (bits 5–7) are updated when reception of that data is com-
plete.  Once S0STAT1 is set to "1" ("1": error occurred), it is not reset to "0" even if that
error has not occurred at completion of the next reception. Therefore, with the program,
reset to "0" any S0STAT1 bits that are "1" after reception is complete. Read the con-
tents of S0BUF1 and S0BUF2 before resetting the OERR01 and OERR02 flags in
S0STAT1. If the contents of S0BUF1 and S0BUF2 are not read, the OERR01 and
OERR02 flags will be set to "1" again regardless of whether an overrun error occurs in
the next receive operation.

At reset (when the 

RES

 signal is input, the BRK instruction is executed, the watchdog

timer is overflown, or an operation code trap is generated), S0STAT1 becomes 11H.

Figure 15-6 shows the configuration of S0STAT1.

<Description of Each Bit>

• OERR01 (bit 1)

When an SCI0 receive operation is complete and the receive data is transferred into
S0BUF1, OERR01 is set to "1" if the data transferred into S0BUF1 for the previous
reception has not yet been read by the CPU. New receive data is loaded into
S0BUF1 even if OERR01 has been set.  (Overrun error)

• PERR01 (bit 2)

With SCI0, the parity of data received by S0BUF1 is compared to the parity bit
appended to and transferred with the data. If they do not match, PERR01 is set to
"1".  (Parity error)

• MERR01 (bit 3)

During the SCI0 UART multiprocessor communication mode, MERR01 is set to "1" if
an address is transmitted while S0BUF1 is receiving data. In other words, when the
MPC bit (of the data that is transferred when the SR0MPC bit of SR0CON is "0") is
"1", MERR01 is set to "1", interpreting this as a multiprocessor communication error.

• OERR02 (bit 5)

When an SCI0 receive operation is complete and the receive data is transferred into
S0BUF2, OERR02 is set to "1" if the data transferred into S0BUF2 for the previous
reception has not yet been read by the CPU. New receive data is loaded into
S0BUF2 even if OERR02 has been set. (Overrun error)

Summary of Contents for MSM66591



















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands