New lift FST, Manual

Page: 125 / 174

1 Menu tree
1.4 MAIN MENU – Config
FST_HB.EN04/03
123
Car-Operate-Panel –
Display-2
Function of pin X4.5 on the FPM Car-Operate-Panel. See
“Display-0 … 2” on page 128. 00000000 ....
11111111
Car-Operate-Panel –
OPEN = A+B
The door open signal (FPM X4.35 or X4.36) is active for all car
doors. YES
NO
Car-Operate-Panel –
CLOSE = A+B
The door close signal (FPM X4.2 or X4.3) is active for all car
doors. YES
NO
Car-Operate-Panel –
OPEN = last
The door open signal (FPM X4.35 or X4.36) is only active for
the car door last opened. YES
NO
Car-Operate-Panel –
Divider-Door
Car door control for lifts with a too large footprint of the car.
This parameter must only be activated if there is a car door. If
this parameter is activated the FPM input “Door A Open”
(X4.35) is used to query the door divider contact (normally
closed)! If the divider door is open the input is activated and
the car will be shut down on the current floor with
“OVERLOAD”. The “OVERLOAD” state can be reset with the
input “CAR PRIORITY” on the FPM (key switch on the inside
panel, X4.37). YES
NO
Car-Operate-Panel –
Card Reader
Control of a card reader to enable in-car calls. Only activate
after consulting NEW LIFT. This requires a modification of the
system specific wiring! If this parameter is activated, no in-car
calls can be placed without a card reader! YES
NO
Car-Operate-Panel –
-"- Clear Opt
Delete pending in-car calls when activating the card reader. YES
NO
Car-Operate-Panel –
Chime–Roof
Separate landing chime for upward travel installed on the car
roof. The chime signal is issued on FPM output „Display-1“, if
parameter
Display-1=00000000
is set (see “Display-0
… 2” on page 128).
YES
NO
Car-Operate-Panel –
Chime–Floor
Separate landing chime for downward travel installed below
the car floor. The chime signal is issued on FPM output
„Display-2“, if parameter
Display-2=00000000
is set
(see “Display-0 … 2” on page 128).
YES
NO
Car-Operate-Panel –
DoorOpen NC
Interpret the door open signal (FPM X4.35 or X4.36) as
normally closed contact. YES
NO
Car-Operate-Panel –
O-Load Blink
Activate flashing mode of the overload display (FPM X4.6). YES
NO
Car-Operate-Panel –
Pin-34 Functn
Function of input X4.34 of the FPM (see “Pin-34 Functn” on
page 129). 0 .. 99
Car-Operate-Panel –
3xCall=Clear
An already acknowledged in-car call can be deleted by placing
the call another three times. YES
NO
Fireman Options
Fire Standards
Fire standard the fireman mode complies to (see Manual for
Fireman Mode). TRA-266
AS-1735 (Australia)
HongKong
SIA
Fireman Options
Fire–>Fireman (ADM)
A fire signal issued through an ADM landing button module
automatically activates the fireman mode after reaching the
floor with the fire (see Manual for Fireman Mode). YES
NO
Fireman Options
Fire–>Fireman (I/O)
A fire signal issued through a programmable input/output
automatically activates the fireman mode after reaching the
floor with the fire (see Manual for Fireman Mode). YES
NO
Fireman Options
Off only in M-Flr
The fireman mode can only be deactivated on the main floor
(see Manual for Fireman Mode). YES
NO
Menu item Description Setting range