New lift FST Manual Download Page 129

Page: 129 / 174

1 Menu tree

1.4 MAIN MENU – Config

FST_HB.EN04/03

127

Show LON Module

After completing the “Search LON Modules” function the FST provides a
list with all LON Modules connected to the LON bus.

The list is structured as follows:

ADM-Bus Masks

The bus masks are two-digit hex values.

The first LON Module of five total is displayed.

Module Type “FSM” with software version “00117”, appendix “010/
002”.

LON-ID of the module: „010030496900“

First four configuration bytes of the module.

Switch to configuration bytes 5 … 12

Show next LON Module.

Show last LON Module.

Toggle line C of ADM Modules.

Configuration bytes 1 … 4 of the module.

Configuration bytes 5 … 8 of the module.

Configuration bytes 9 … 12 of the module.

Landing button module on floor 02, door side A and bus line 0.

LON Module [001\005]
Prg:FSM00117 010\002
ID:01 00 30 49 69 00
[00] [00] [00] [00]

ID:01 00 30 49 69 00
[00] [00] [00] [00]
[00] [00] [00] [00]
[00] [00] [00] [00]

LON Module [004\005]
Prg:ADR00112 010\002
Floor=02 Door=A BS=0
[00] [00] [00] [00]

Fig. 1.12

Function of the individual bits

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands