New lift FST Manual Download Page 14 | Manualshive

Page: 14 / 174

background image

3 FST-Controller user interface
3.1 LC-Display and messages

12

FST_HB.EN04/03

LIFT OFF

The controller has been switched off. Possible
switch-off points:

-

Car light failure

-

Input “Car Light OFF”, FST X7.14

-

Programmable input/output of a RIO module
(external)

-

Programmable input/output of the FST-
Controller

-

Externally by the GST Group Controller or the
LMS lift monitoring system

See “Source of special drive signals

” on page 24.

FIREMAN MODE

Fireman mode has been activated. Possible
sources:

-

Key switch on the in-car control panel (FPM
X4.4)

-

Programmable input/output of the FST-
Controller

-

The state was saved after a power failure and
has been reconstructed. Function

Fireman

Mode Reset

must be used to reset this

state, see “Fireman Options” on page 123.

-

Key switch on the landing control panel (ADM
input X3.12 / X3.13)

-

GST Group Controller (see GST Manual)

See “Source of special drive signals

” on page 24.

FILE TRANSFER

ACTIVE

The controller is in remote data transmission
mode to transfer files to a GST Group
Controller or to a PC.

INSPECTION

The controller is in inspection mode (input FSM
X12.2).
Attention: Line A of the FST display must show

EMERGENCY STOP

!

CALIBRATION -

The calibration drive has been started. The
number of remaining drives is displayed (see
“Calibration drive” on page 117).

LEARN DRIVE ACTIVE

The controller performs a learn drive, see
“Learn drive” on page 117.

LEARN DRIVE-START

The controller performs a learn drive, see
“Learn drive” on page 117.

LEARN DRIVE-OK!

The learn drive has been completed, see
“Learn drive” on page 117.

LEARN DRIVE-ABORT!

The learn drive has been aborted due to a fault.
The reason for the abortion is entered in the
error list, see “Learn drive” on page 117 and
“Error List” on page 151.

SAFETY CURTAIN

The safety curtain replacing the car door has
been interrupted. The contact is in the safety
circuit instead of the car door contacts (see
System description – Safety curtain).

Display

Description

«
...
12
13
14
15
16
...
»

Summary of Contents for FST















































































































































































Reviews:

No comments

Related manuals for FST

Brand: ABB Pages: 2

Brand: Aalborg Pages: 128

Brand: CAME Pages: 98

Brand: CAME Pages: 16

Brand: CAME Pages: 8

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: dbx Pages: 52

Brand: Hankscraft Runxin Pages: 58

Brand: Zeagle Pages: 37

Brand: National Instruments Pages: 29

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands