New lift FST Manual Download Page 120

Page: 120 / 174

1 Menu tree
1.4 MAIN MENU – Config

118

FST_HB.EN04/03

Prio-Landing/Car –

Keep landing calls

After activating “soft” priority car, landing calls will also be
kept.

YES
NO

Park Drive –

Enable

Enable park drive program.

YES
NO

Park drive –

Program

Parking drive characteristics of the lift system (see “Park Drive
Programs” on page 126).

Auto Test Drive –

Mode

Automatic call generation for testing purposes. Drive
characteristics of the Auto Test Drive:

Sequence: floors are approached sequentially
(0,1,2,3,2,1,0,1,...)

Shuttle: car shuttles between “Lo-Limit” and “Hi-Limit”.

Random: floors are approached in a random sequence.

Sequence
Shuttle
Random

Auto Test Drive –

In-car calls

Automatically generated in-car calls during the auto test drive.

YES
NO

Auto Test Drive –

Landing calls

Automatically generated landing calls during the auto test
drive.

YES
NO

Auto Test Drive –

Doors

Enables the car doors during the auto test drive. The set value
corresponds to the following bit mask:

0 ... 7

Auto Test Drive –

Floor-Limit

When activated only floors between

Lo-Limit

and

Hi-

Limit

will be approached.

YES
NO

Auto Test Drive –

Lo-Limit

Lowest floor of the auto test drive.

0 ... top floor

Auto Test Drive –

Hi-Limit

Highest floor of the auto test drive.

0 ... top floor

Auto Test Drive –

Time-Limit

The auto test drive will be disabled automatically after two
hours.

YES
NO

Auto Test Drive –

Interval

Time between two commands during the auto test drive.

0 ... 255 sec

LON Configuration

Search LON Modules

A bus scan is carried out to determine the modules connected
to the bus. All LON modules connected to the bus will be
entered in a table that can be displayed with

Show LON

Modules

YES
NO

LON Configuration

Show LON Modules

Displays all LON modules connected to the bus The list of
LON modules is generated/updated with the menu item

Search LON Modules

. See “Show LON Module” on

page 127.

Read only

Modem / Fax / LMS

LMS floor-locking

Enable external floor-locking via remote data transmission
(LMS Lift Monitoring System).

YES
NO

Modem / Fax / LMS

FST FAX Enable

Enables all fax functions (see Installation & Commissioning –
Fax modem).

OFF
ON

Modem / Fax / LMS

Tel. Number FST

Phone number of the FST modem (see Installation &
Commissioning – Fax modem).

ASCII

Menu item

Description

Setting range

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands