New lift FST Manual Download Page 144 | Manualshive

Page: 144 / 174

background image

1 Menu tree
1.7 MAIN MENUE – System

142

FST_HB.EN04/03

Recorder –

Filter Setting

RIO Traffic

Enable event channel “RIO Traffic” for recording. See “Event
Channels” on page 143.

ON
OFF

Recorder –

Stop-when-full

Determines if recordings stops when the PC-Card is full.
Otherwise recording continues at the start of the card (endless
loop).

YES
NO

Update FST

Update the FST software with a PC-Card.

³

YES
NO

Update GST

Update the GST software with a PC-Card.

³

YES
NO

Update LON-Modules

Update all connected LON-Modules if a new software version
is available on the PC-Card.

³

YES
NO

Config --> Backup

Create a backup copy of the current FST configuration for
storage in an internal buffer.

³

YES
NO

Config <-- Backup

Load the FST configuration from the internal buffer as current
FST configuration. All parameters will be overwritten. Only
activate this parameter after consulting NEW LIFT!

³

YES
NO

PC-Card Tools –

Config --> Card

Save current FST configuration on PC-Card.

³

YES
NO

PC-Card Tools –

Config <-- Card

Load the FST configuration from the PC-Card as current FST
configuration. All parameters will be overwritten. Only activate
this parameter after consulting NEW LIFT!

³

YES
NO

PC-Card Tools –

S/Ware --> Card

Save current FST software on PC-Card.

³

YES
NO

PC-Card Tools –

Clear Card

Delete everything on the PC-Card.

³

YES
NO

Panel Test

Special function to test landing and in-car panels (see System
description – Panel Test).

FST Reset!

RESET the FST-Controller.

³

YES
NO

Menu item

Description

Setting range

«
...
142
143
144
145
146
...
»

Summary of Contents for FST















































































































































































Reviews:

No comments

Related manuals for FST

Brand: ABB Pages: 52

Brand: Panasonic Pages: 16

ESD-5550 Series

Brand: GAC Pages: 12

Brand: jbc Pages: 44

Brand: jbc Pages: 8

Digiplex DGP-848

Brand: Paradox Pages: 20

Brand: Samson Pages: 6

Brand: Union Instruments Pages: 63

Brand: Yoshitake Pages: 4

Brand: YOKOGAWA Pages: 20

UTAdvanced UT32A

Brand: YOKOGAWA Pages: 3

Wireless Blade FX Controller for Wii

Brand: Datel Pages: 2

Brand: Technische Alternative Pages: 68

Brand: TechGrow Pages: 34

Brand: Olsen Pages: 4

Brand: Quickie Pages: 64

Brand: Kamstrup Pages: 7

Brand: Kohzu Precision Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands