New lift FST Manual Download Page 137 | Manualshive

Page: 137 / 174

background image

1 Menu tree

1.5 MAIN MENU – Positioning

FST_HB.EN04/03

135

Positioning Parameters

For a better understanding of the parameters for linear and incremental
positioning the main settings are shown graphically in the following two
figures.

Increm. Positng. –

Auto-Orien.

With incremental positioning an orientation drive to the top or
bottom landing is required after switching the controller on and
off (also after a power failure). The orientation drive is started
automatically after switching the FST-Controller on. Only
change this parameter after consulting NEW LIFT!

YES
NO

Increm. Positng. –

Orien delay

Delay of the orientation drive after switching the FST-
Controller on.

0 ... 9999 ms

Increm. Positng. –

Corr.Bottom

Position of the switch for bottom correction in [mm]. This is an
absolute value. To determine the distance to the bottom floor
the absolute value of the bottom floor must be subtracted from
the value entered here (see “Position ABS” on page 132). The
value is determined automatically during the learn drive and
must not be changed!

0 ... 9999999 mm

Increm. Positng. –

Corr.Top

Position of the switch for top correction in [mm]. This is an
absolute value. To determine the distance to the top floor the
value entered here must be subtracted from the absolute
value of the top floor (see “Position ABS” on page 132). The
value is determined automatically during the learn drive and
must not be changed!

0 ... 9999999 mm

Increm. Positng. –

ZoneB–Length

Length of the zone signal when relevelling with the BO/BU
switch. This value is determined automatically during the learn
drive.

0 ... 250 mm

Increm. Positng. –

BOBU<->Runoff

Length of the BO/BU signal when relevelling with the BO/BU
switch. This value is determined automatically during the learn
drive.

0 ... 250 mm

Increm. Positng. –

ZoneB–Hysters

Length of the hysteresis of zone switch B. This value is
determined automatically during the learn drive and is limited
to 10 mm by the software. In case of problems with the
levelling adjustment the levelling for upward travel can be
adjusted as described in the installation manual and the
levelling for downward travel can be adjusted by changing the
hysteresis value.

-100 ... 100 mm

Increm. Positng. –

ZoneB–Level

Level of zone switch B if the car is in the door zone.

-

LO: 0V (closed)

-

HI: +24V (open, default)

The setting must correspond to jumper JMP7 on the FST
circuit board (see “Jumper JMP7” on page 43).

LO
HI

Increm. Positng. –

ZoneB–Debnce

Debounce time of zone switch B. Only change this value after
consulting NEW LIFT!

0 ... 40 msec

Increm. Positng. –

CB/CT–Level

Level of the CB/CT switch if the car is at the top or bottom
landing.

-

LO: 0V DC

-

HI: +24V (default)

The setting must correspond to jumper JMP7 on the FST
circuit board (see “Jumper JMP7” on page 43).

LO
HI

Menu item

Description

Setting range

«
...
135
136
137
138
139
...
»

Summary of Contents for FST















































































































































































Reviews:

No comments

Related manuals for FST

Brand: MADRIX Pages: 36

Minas A4 Series

Brand: Panasonic Pages: 5

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 12

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 10

Brand: Danfoss Pages: 20

Brand: Olsberg Pages: 68

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

Brand: Danfoss Pages: 16

Consolidated 2900-40 Series

Brand: Baker Hughes Pages: 80

Brand: Cardin Elettronica Pages: 56

Brand: Radionics Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands