New lift FST Manual Download Page 153

Page: 153 / 174

6 Error List

6.1 LC-Display

FST_HB.EN04/03

151

Error List

The FST-Controller stores up to 100 event and error messages. These
messages can be called up on the user interface of the FST, with the PC-
Card or via remote data transmission at any time.

6.1 LC-Display

6.2 Keypad functions

Event/error no. 37 of 40 total

Date / Time / Message Code

Text description of event/error

Floor /
Generated signals (see “Positionsmeldungen Kop: Virt=0b Real=00”
on page 22) /
actual signals (see “Positionsmeldungen Kop: Virt=0b Real=00” on
page 22) /
information byte Infobyte1 (see “Error messages” on page 153)

Event/error no. 37 of 40 total

Date / Time / Message Code

Text description of event/error

Information bytes: Infobyte2 .. Infobyte8

ERROR [00037\00040]
28.09 10:18:26 [012]
Door Close Failed
FLOOR:03 V00 R01 I00

ERROR [00037\00040]
28.09 10:18:26 [012]
Door Close Failed
01 02 00 00 00 00 00

Switch to 2nd to 8th information byte

Back to first screen

Scroll error list up

Scroll error list down

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands