New lift FST Manual Download Page 130

Page: 130 / 174

1 Menu tree
1.4 MAIN MENU – Config

128

FST_HB.EN04/03

Car ventilator

Display-0 … 2

The FPM outputs “Display-0 … 2” can display various operating states of
the system. The states to be displayed are set to “1” in the respective
control register according to the following diagram.

If no operating states are selected in the control register (“00000000”) the
outputs “Display-1” and “Display-2” can have the following functions:

Display-1

Issue “Chime–Roof” signal if

Chime–Roof=YES

is set (see “Chime–

Roof” on page 123).

Load display for “Loading Function” (see “Loading Function” on
page 129).

Lift-Boy Mode buzzer (see “Lift-Boy Mode” on page 139).

Setting

Description

Switched Off

The car ventilator is switched off.

Manual On/Off

The car ventilator is switched on and off with a button
on the in-car panel (input FPM X4.1).

Off-

Delay

The car ventilator is switched on with a button on the
in-car panel (input FPM X4.1) and switched off after
an adjustable delay (see

Vent. Off Delay

)

AuOff-

Delay

The car ventilator is switched on automatically for
each drive and switched off after an adjustable delay
(see

Vent. Off Delay

)

Fig. 1.13

Function of the individual bits

Summary of Contents for FST















































































































































































Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands

New lift FST, Manual

Search results

Summary of Contents for FST

Reviews:

Related manuals for FST

Brands by name

Popular brands