NEC V850E/MS1 UPD703100 User Manual Download Page 410

Page: 410 / 449

CHAPTER 13 RESET FUNCTIONS

User’s Manual U12688EJ4V0UM00

410

(1) Receiving the reset signal

RESET (input)

Internal system
reset signal

Eliminate as a noise

∆

Reset

acceptance

Reset

release

Analog
delay

Note

Note The internal system reset signal continues in the active state for at least 4 system clock cycles after

reset clear timing by the RESET signal.

(2) Reset during power on

In the reset operation during power on (when the power is turned on), in accordance with the low-level width of

the RESET signal, it is necessary to secure an oscillation stabilization time of 10 ms or greater from power rise

to the reception of the reset.

RESET (input)

Oscillation stabilization
time

Analog delay

∆

Reset release

13.3 Initialization

The initial values of the CPU, internal RAM and internal peripheral I/O after reset are shown in Table 13-2.

Initialize the contents of each register as necessary during program operation. Particularly, the registers shown

below are related to system settings, so set them as necessary.

{

Power save control register (PSC): Sets the functions of pins X1 and X2, the operation of the CLKOUT pin, etc.

{

Data wait control register (DWC): Sets the number of data wait states.

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands

NEC V850E/MS1 UPD703100, User Manual

Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands