manualshive.com logo in svg

NEC V850E/MS1 UPD703100, User Manual

The "NEC V850E/MS1 UPD703100" User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and information on how to effectively operate and utilize the features of this product. Access the manual at manualshive.com to enhance your experience with the NEC V850E/MS1 UPD703100.

Share
Download
background image

CHAPTER  11   A/D  CONVERTER

User’s Manual  U12688EJ4V0UM00

345

11.8 Operating Precautions

11.8.1 Stopping conversion operation

When 0 is written to the CE bit of the ADM0 register during a conversion operation, the conversion operation stops

and the conversion results are not stored in the ADCRn register (n = 0 to 7).

11.8.2 External/timer trigger interval

Set the interval (input time interval) of the trigger in the external or timer trigger mode longer than the conversion

time specified by the FR2 to FR0 bits of the ADM1 register.

(1) When interval = 0

When several triggers are input simultaneously, the analog input with the smaller ANIn pin number is

converted.  The other trigger signals input simultaneously are ignored, and the number of trigger inputs is not

counted.  Therefore, the generation of interrupts and storage of results in the ADCRn register will become

abnormal (n = 0 to 7).

(2) When 0 < interval 

≤≤≤≤

 conversion operation time

When the timer trigger is input during a conversion operation, the conversion operation stops and the

conversion starts according to the last timer trigger input.

When a conversion operation stops, the conversion results are not stored in the ADCRn register.  However,

the number of trigger inputs is counted, and when the interrupt is generated, the value at which conversion

ended is stored in the ADCRn register.

11.8.3 Operation of standby mode

(1) HALT mode

The A/D conversion operation continues.  When released by the NMI input, the ADM0 and ADM1 registers

and ADCRn register hold the value (n = 0 to 7).

(2) IDLE mode, STOP mode

As clock supply to the A/D converter is stopped, no conversion operations are performed.  When  these modes

are released using the NMI input, the ADM0 and ADM1 registers and the ADCRn register hold the value.

However, when the IDLE and software STOP modes are set during a conversion operation, the conversion

operation stops.  At this time, if released using the NMI input, the conversion operation resumes, but the

conversion result written to the ADCRn register will become undefined.

In the IDLE and software STOP modes, operation of the comparator is also stopped to reduce the power

consumption, and to further reduce current consumption, set the voltage of the AV

REF

 to V

SS

.

11.8.4 Compare match interrupt when in timer trigger mode

The compare register’s match interrupt becomes an A/D conversion start trigger and starts the conversion

operation.  When this happens, the compare register’s match interrupt functions even if it is a compare register match

interrupt directed to the CPU.  In order to prevent match interrupts from the compare register being directed to the

CPU, disable interrupts by the interrupt mask bits (P11MK0 to P11MK3) of the interrupt control register (P11IC0 to

P11IC3).

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for V850E/MS1 UPD703100

Accel 300+ Installation Instructions Manual preview
300+
Brand: Accel Pages: 8
Unipulse F160 Operation Manual preview
F160
Brand: Unipulse Pages: 99
Mainpine EPC Operating Instructions Manual preview
EPC
Brand: Mainpine Pages: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Brand: Danfoss Pages: 20
Maestra 8080 User Manual preview
8080
Brand: Maestra Pages: 22
Samson 3730-6 Mounting And Operating Instructions preview
3730-6
Brand: Samson Pages: 124
Samson TROVIS 5500 Operating Instructions Manual preview
TROVIS 5500
Brand: Samson Pages: 86
VAC V100 Troubleshooting Manual preview
V100
Brand: VAC Pages: 5
SYCLOPE TRACE'O Manual preview
TRACE'O
Brand: SYCLOPE Pages: 60
Bailey infi 90 IMMFP12 Instruction preview
infi 90 IMMFP12
Brand: Bailey Pages: 75
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Brand: Allen-Bradley Pages: 16
TWR Lighting E-1DB2 Manual preview
E-1DB2
Brand: TWR Lighting Pages: 49
Delta DZNT-104T Installation Manual preview
DZNT-104T
Brand: Delta Pages: 16
Danfoss AME 15 QM Instructions Manual preview
AME 15 QM
Brand: Danfoss Pages: 14
Current Mini LOOP BT Quick Start Manual preview
Mini LOOP BT
Brand: Current Pages: 4
PEAS VC-530E User Manual preview
VC-530E
Brand: PEAS Pages: 4
Sollae Systems CIE-M10A User Manual preview
CIE-M10A
Brand: Sollae Systems Pages: 72
TAC Vista TAC Xenta OP Manual preview
TAC Xenta OP
Brand: TAC Vista Pages: 2

Brands by name

Popular brands

Load more brands