NEC V850E/MS1 UPD703100 User Manual Download Page 242

Page: 242 / 449

CHAPTER 8 CLOCK GENERATOR FUNCTIONS

User’s Manual U12688EJ4V0UM00

242

8.5.5 Software STOP mode

(1) Settings and operating state

In this mode, the clock generator (oscillator and PLL synthesizer) is stopped. The system overall is stopped,

and it enters an ultra-low power consumption state where only device leakage current is lost.

It is possible to enter the software STOP mode by setting the PSC register (specific register) using a store

instruction (ST/SST instruction) or a bit manipulation instruction (SET1/CLR1/NOT1 instruction) in software

(refer to 3.4.9 Specific registers).

In the case of the PLL mode and oscillator connection mode (CESEL bit of the PSC register = 0), it is

necessary to secure the oscillation stabilization of the oscillator after releasing the software STOP mode.

In the software STOP mode, program execution stops, but all the contents of all the registers, internal RAM,

and ports are held in the state they were in just before entering the software STOP mode. Operation of the

internal peripheral I/O (except the ports) is also stopped.

The status of each hardware unit during the software STOP mode is as shown in Table 8-5.

Caution In the case of the direct mode (CKSEL pin = 1) or external clock connection mode (CESEL bit

of the PSC register = 1), the software STOP mode cannot be used.

Table 8-5. Operating States When in Software STOP Mode

Function

Operating State

Clock generator

Stop

Internal system clock

Stop

CPU

Stop

Port

Note

Hold

Internal peripheral I/O (except ports)

Stop

Internal data

Note

All the CPU’s registers, status, data, internal RAM contents,

other internal data, etc. are retained in the state they were

in before entering the HALT mode.

D0 to D15

A0 to A23

RD, WE, OE, BCYST

High-impedance

LWR, UWR, IORD, IOWR

CS0 to CS7

High-level output

RAS0 to RAS7

LCAS, UCAS

REFRQ

Operating

HLDRQ

Input (no sampling)

HLDAK

High-impedance

When in external

expansion mode

WAIT

Input (no sampling)

CLKOUT

Low-level output

Note If the V

value is within the operable range.

However, even when it drops below the minimum operable voltage, if the data hold voltage V

DDDR

maintained, the contents of internal RAM only are held.

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands

NEC V850E/MS1 UPD703100, User Manual

Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands