NEC V850E/MS1 UPD703100 User Manual Download Page 265

Page: 265 / 449

CHAPTER 9 TIMER/COUNTER FUNCTION (REAL-TIME PULSE UNIT)

User’s Manual U12688EJ4V0UM00

265

9.4.4 Clearing/starting timer by TCLR1n signal input

Timer 1 ordinarily starts a counting operation when the CE1n bit in the TMC1n register is set (1), but TM1n can be

cleared and a count operation started by input of the TCLR1n signal (n = 0 to 5).

If the ECLR1n bit of the TUM1n register is set to 1, and the OSTn bit is set to 0, if the active edge is input to the

TCLR1n signal after the CE1n bit is set (1), the counting operation starts. Also, if the active edge is input to the

TCLR1n signal during operation, the TM1n’s value is cleared and the count operation resumes (refer to Figure 9-3).

If the ECLR1n bit of the TUM1n register is set to 1, and the OSTn bit is set to 1, the counting operation starts if the

active edge is input to the TCLR1n signal after the CE1n bit is set (1). If TM1n overflows, the count operation stops

once and it does not resume the count operation until the active edge is input again to the TCLR1n signal. If the

active edge of the TCLR1n signal is detected during a counting operation, TM1n is cleared and the count operation

continues (refer to Figure 9-4). Note that if the CE1n bit is set (1) after an overflow, the count operation does not

resume.

Figure 9-3. Timer Clear/Start Operation by TCLR1n Signal Input (If ECLR1n = 1 and OSTn = 0)

Clear & start

Overflow

FFFFH

TM1n

Count
start

INTOV1n

ECLR1n 1

CE1n 1

TCLR1n

Remark

n = 0 to 5

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands

NEC V850E/MS1 UPD703100, User Manual

Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands