NEC V850E/MS1 UPD703100 User Manual Download

Page: 341 / 449

CHAPTER 11 A/D CONVERTER

User’s Manual U12688EJ4V0UM00

341

11.7 Operation in External Trigger Mode

In the external trigger mode, the analog inputs (ANI0 to ANI3) are A/D converted by the ADTRG pin input timing.

The ADTRG pin is also used as the P127 and INTP153 pins. To set the external trigger mode, set the PMC127 bit

of the PMC12 register to 1 and bits TRG2 to TRG0 of the ADM1 register to 110.

For the valid edge of the external input signal in the external trigger mode, the rising edge, falling edge, or both

rising and falling edges can be specified using bits ES531 and ES530 of the INTM6 register. For details, refer to 7.3.8

(1) External interrupt mode registers 1 to 6 (INTM1 to INTM6).

11.7.1 Select mode operations (external trigger select)

One analog input (ANI0 to ANI3) specified by the ADM0 register is A/D converted. The conversion results are

stored in the ADCRn register corresponding to the analog input. There are two select modes, 1-buffer mode and 4-

buffer mode, storing the conversion results (n = 0 to 3).

(1) 1-buffer mode (External trigger select: 1-buffer)

One analog input is A/D converted using the ADTRG signal as a trigger. The conversion results are stored in

one ADCRn register. The analog input and the A/D conversion results register correspond one to one. INTAD

interrupts are generated after each A/D conversion, and A/D conversion ends.

Trigger

Analog Input

A/D Conversion Result Register

ADTRG signal

ANIn

ADCRn

(n = 0 to 3)

While the CE bit of the ADM0 register is 1, the A/D conversion is repeated every time a trigger is input from the

ADTRG pin.

This is most appropriate for applications that read the results each time there is an A/D conversion.

Figure 11-15. Example of 1-Buffer Mode (External Trigger Select 1-Buffer) Operation

ANI0

ANI1

ANI2

ANI3

ADCR0

ADCR1

ADCR2

ADCR3

ADCR4

ADCR5

ADCR6

ADCR7

A/D converter

ADTRG

(1)

CE bit of ADM0 is set to 1 (enable)

(2)

External trigger generation

(3)

ANI2 A/D conversion

(4)

Conversion result is stored in ADCR2

(5)

INTAD interrupt generation

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands

NEC V850E/MS1 UPD703100, User Manual

Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands