NEC V850E/MS1 UPD703100 User Manual Download Page 287

Page: 287 / 449

CHAPTER 10 SERIAL INTERFACE FUNCTION

User’s Manual U12688EJ4V0UM00

287

10.2.3 Control registers

(1) Asynchronous serial interface mode registers 00, 01, 10, 11 (ASIM00, ASIM01, ASIM10, ASIM11)

These registers specify the UART0 and UART1 transfer mode.

These registers can be read/written in 8- or 1-bit units.

TXE0

ASIM00

RXE0

PS01

PS00

CL0

SL0

SCLS01

SCLS00

FFFFF0D0H

TXE1

ASIM10

RXE1

PS11

PS10

CL1

SL1

SCLS11 SCLS10

80H

Address

FFFFF0C0H

After reset

80H

Bit Position

Bit Name

Function

Transmit/Receive Enable

Specifies the transmission/reception enable status/disable status.

TXEn

RXEn

Operation

Transmission/reception disabled (CSIn selected)

Reception enabled

Transmission enabled

Transmission/reception enabled

7, 6

TXEn,

RXEn

When reception is disabled, the receive shift register does not detect the start bit. The

receive buffer contents are held without shift-in processing or transmit processing to the

receive buffer being performed.

While in the reception enabled state, the receive shift operation is started in

synchronization with detection of the start bit and after 1 frame of data has been

received, the contents of the receive shift register are transmitted to the receive buffer.

Also, the reception complete interrupt (INTSRn) is generated in synchronization with

transmission to the receive buffer. The TXDn pin becomes high impedance when

transmission is disabled and a high level is output if it is not transmitting when

transmission is enabled.

Remark

n = 0, 1

Summary of Contents for V850E/MS1 UPD703100


































































































































































































































































































































































































































































Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands

NEC V850E/MS1 UPD703100, User Manual

Search results

Summary of Contents for V850E/MS1 UPD703100

Reviews:

Related manuals for V850E/MS1 UPD703100

Brands by name

Popular brands