manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 122

2.

Unscrew locknut (1) and remove with wash-
er (2).

3.

Unscrew locknut (4) and remove with wash-
er (5).

4.

Remove coupling rod (3) with washer (6).

Installing coupling rod

1.

Install coupling rod (3) and washer (6).

2.

Fit nut (1) with washer (2) and tighten to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Locknut

-

Tightening torque

(Assembly compound
(Molykote P 37))

16 Nm ±2 Nm

3.

Fit nut (4) with washer (5) and tighten to specified torque using a torque wrench.

4.

Mount guard panel (1).

5.

Tighten locking screws (2, 5) to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Locking screw

-

Tightening torque

(Assembly compound
(Molykote P 37))

35 Nm ±2 Nm

122 | Exhaust Gas Recirculation | MS150100/06E 2017-08

TIM-ID: 0000078337 - 001

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands