manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 135

8.8.2 Engine oil – Change

Preconditions

☑

Engine is stopped and starting disabled.

☑

Engine is at operating temperature.

☑

MTU Fluids and Lubricants Specifications (A001063/..) are available.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 20–100 Nm

F30026582

1

Engine oil
Sealing ring

(→ Spare Parts Catalog)

O-ring

(→ Spare Parts Catalog)

WARNING

Oil is hot.
Oil can contain residue/substances which are harmful to health.
Risk of injury and poisoning!
• Allow the product to cool to below 50 °C before beginning work.
• Wear protective clothing, protective gloves and goggles/safety mask.
• Avoid contact with skin.
• Do not inhale oil vapor.

Draining engine oil from stand-
ard oil pan

1.

Provide a suitable vessel to collect the oil.

2.

Remove drain plug (1) and drain oil.

3.

Insert drain plug (1) and tighten to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Drain screw

M26x1.5

Tightening torque

(Engine oil)

100±10 Nm

4.

Replace engine oil filter (→ Page 137).

MS150100/06E 2017-08

| Lube Oil System, Lube Oil Circuit | 135

TIM-ID: 0000028016 - 003

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands