manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 143

8.10.4 Engine coolant – Filling

Preconditions

☑

Engine is stopped and starting disabled.

☑

MTU Fluids and Lubricants Specifications (A001063/..) are available.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Coolant

DANGER

Components are moving or rotating.
Risk of crushing, danger of parts of the body being caught or pulled in!
• Operate the engine at low load only. Keep clear of the danger zone of the engine.

WARNING

Coolant is hot and under pressure.
Risk of injury and scalding!
• Let the engine cool down.
• Wear protective clothing, gloves, and goggles / safety mask.

WARNING

High level of engine noise when the engine is running.
Risk of damage to hearing!
• Wear ear protectors.

NOTICE

Cold coolant in hot engine can cause thermal stress.
Possible formation of cracks in the engine!
• Fill / top up coolant only into cold engine.

Preparatory steps

1.

Turn valve cover (1) on coolant expansion
tank counterclockwise to the first stop and
allow pressure to escape.

2.

Continue to turn valve cover (1) counter-
clockwise and remove.

MS150100/06E 2017-08

| Coolant Circuit, General, High-Temperature Circuit | 143

TIM-ID: 0000000909 - 008

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands