manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 163

Installing Lambda sensor

Note:

When the sensor was subjected to shock or
impact load, it is deemed to be defective and
may not be used.

1.

Remove protective cap on thread only just
before installation.

Note:

Do not wipe off the thread lubricant applied
by the manufacturer.

2.

Apply specified assembly compound to sen-
sor thread if required.

3.

Screw in sensor by hand.

4.

Tighten nut (2) to specified torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Nut

M18 x 1.5 Tightening torque

(Assembly compound
(Molykote P 37))

40 Nm +4 Nm

5.

Fit male connector (1) and latch it.

6.

Reset Lambda sensor calibration with DiaSys® (→ Dialog system DiaSys® E531920/..). If no DiaSys® is
available, contact Service.

MS150100/06E 2017-08

| Accessories for (Electronic) Engine Governor / Control System  | 163

TIM-ID: 0000025194 - 017

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands