manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 162

8.16.4 Lambda sensor – Replacement

Preconditions

☑

Engine is stopped and starting disabled.

☑

Power supply to electronic engine management system is switched off.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 10–60 Nm

F30452769

1

Ratchet adapter

F30027340

1

Assembly compound (Molykote P 37)

50564

1

Lambda sensor

(→ Spare Parts Catalog)

1

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

NOTICE

Ceramic cell breakage due to shock or impact.
Risk of damage to components!
• Avoid shocks and impacts.
• Exercise extreme care when handling sensors.

NOTICE

High voltage.
Risk of damage to components!
• Switch off ignition before replacing components.

Removing Lambda sensor

1.

Observe the following general information:
• Layout and position of sensor (→ Page 25).

2.

Unplug and remove male connector (1).

3.

Remove sensor (2).

162 | Accessories for (Electronic) Engine Governor / Control System  | MS150100/06E 2017-08

TIM-ID: 0000025194 - 017

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands