manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 128

2.

Install actuator (3) with holder (6) and cou-
pling rod (4) on turbine housing.

3.

Install screws (1) with washers (2) and use torque wrench to tighten to specified tightening torque.

Name

Size

Type

Lubricant

Value/Standard

Hex screw

M8x25

Tightening torque

(Assembly paste (Ul-
tra-Therm MTU))

18 Nm +2 Nm

Note:

The coupling rod (4) must be connected under tensile stress with the lever.

4.

Connect coupling rod (4) with lever of flap and install lockwasher (5).

5.

Install screw (2) with washer (1) and tighten to specified tightening torque using a torque wrench.

Name

Size

Type

Lubricant

Value/Standard

Hex screw

M8x25

Tightening torque

(Assembly paste (Ul-
tra-Therm MTU))

18 Nm +2 Nm

6.

Use DiaSys® to carry out an actuator test (learning run) (→ Dialog system E531920/..).

128 | Exhaust Gas Recirculation | MS150100/06E 2017-08

TIM-ID: 0000078363 - 001

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands