manualshive.com logo in svg

MTU 10V1600C Series, Operating Instructions Manual

Share
Download
MTU 10V1600C Series Operating Instructions Manual Download Page 121

8.7.3 EGR shutoff flaps – Coupling rod replacement

Preconditions

☑

Engine is stopped and starting disabled.

☑

No operating voltage is applied.

Special tools, Material, Spare parts

Designation / Use

Part No.

Qty.

Torque wrench, 8–40 Nm

F30043446

1

Torque wrench, 4–20 Nm

F30044239

1

Ratchet bit

F30027340

1

Assembly compound (Molykote P 37)

50564

Articulated rod

(→ Spare Parts Catalog)

Locknut

(→ Spare Parts Catalog)

Washer

(→ Spare Parts Catalog)

Screw

(→ Spare Parts Catalog)

WARNING

Actuation mechanism in the exhaust and intake area closes automatically.
Risk of crushing hands!
• To carry out the teach-in routine, keep clear of the safety zone of the actuation mechanism in the

intake and exhaust area.

• Switch off the operating voltage of the engine governor before starting the mechanical test.
• Wear protective goggles.

WARNING

Hot components/surfaces.
Risk of burns!
• Allow the engine to cool down to below 50 °C before beginning work.
• Wear suitable protective equipment/thermal gloves.
• Avoid unprotected contact with hot surfaces.

Removing coupling rod

Note:

For installation positions of EGR shutoff flaps,
refer to overview drawing (→ Page 119).

1.

Unscrew screws (2, 3, 4, 5) and remove
guard panel (1) of EGR shutoff flap.

MS150100/06E 2017-08

| Exhaust Gas Recirculation | 121

TIM-ID: 0000078337 - 001

Summary of Contents for 10V1600C Series

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands