Motorola SC 300 Manual Download Page 31

Page: 31 / 188

Introduction

– continued

DEC 2000

1-3

300 BTS Hardware Installation, ATP and FRU Procedures

PRELIMINARY

The MicroCell, PicoCell and Primary Surge Suppressor can be mounted
indoors (internal) or can be mounted outdoors (external).

Configurations

The MicroCell and PicoCell support single–carrier, omni
configurations.

The cover configurations for the MicroCell and PicoCell units are:

Use solar covers on the Microcell and optional Primary Surge
Suppressor for all outside mounting applications.

Use fin covers on the Microcell or Picocell for indoor applications.

The Primary Surge Suppressor uses solar covers only.

The battery configurations for the MicroCell and PicoCell units are:

Short duration battery

The power configurations for the MicroCell and PicoCell units are:

AC power only

DC power only

AC power with short duration battery

The synchronization configurations for the MicroCell and PicoCell units
are:

Remote GPS Receiver – synchronous operation with High Stability
Oscillator (HSO) backup.

Internal High Stability Oscillator (HSO) only – non–synchronous
operation.

Summary of Contents for SC 300





























































































































































































Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands

Motorola SC 300, Manual

Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands