Motorola SC 300 Manual Download Page 144

Page: 144 / 188

Span Line Daisy Chain Cabling

PRELIMINARY

300 BTS Hardware Installation, ATP and FRU Procedures

DEC 2000

4-36

Objective

The objective of this procedure is to install span line cabling between
multiple BTSs in an open daisy chain configuration.

Background

This feature allows BTSs to be linked together in an open daisy chain
loop using a single T1/JT1/E1 span. This will reduce the number of
spans necessary to support a JCDMA system and minimize unused
channels.

Each BTS may contain up to four units. A maximum of 12 BTSs may
be combined in a single daisy chain.

Cable Description

The following cables are necessary to do this procedure.

Table 4-31: Cable Descriptions and Part Numbers

Cable

Qty.

Part Number

Description

1–3

Customer

Supplied

Span Line Daisy Chain Cable

Procedure

Attach the span line daisy chain cable (Cable N) to the site I/O interfaces
of each BTS. Refer to Figure 4-18 and Table 4-32.

Summary of Contents for SC 300





























































































































































































Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands

Motorola SC 300, Manual

Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands