Motorola SC 300 Manual Download Page 162

Page: 162 / 188

Power, Ground and Battery Cabling for Sites Equipped With Optional
Primary Surge Suppressor

– continued

PRELIMINARY

300 BTS Hardware Installation, ATP and FRU Procedures

DEC 2000

5-14

DC Input Cable Information

The information for the DC input cable(s) (Cable U) is given in
Figure 5-11 and Table 5-4.

Figure 5-11: DC Input Cable Connector Information

SOCKET POSITION ON
CABLE CONNECTOR SHOWN

Table 5-4: DC Input Cable Information

Connector

Wire

Color

Description

Comments

Yellow

Switch A

No connection

Red

Positive

Connect to positive

terminal of supply.

Blue

Switch B

Connect to negative

terminal of supply.

Black

Negative

Connect to negative

terminal of supply.

Procedure

The system configuration determines which power cables are installed.
The ground cable is always installed. Based on the system configuration
perform the appropriate procedures from the following tables.

Table 5-5: Procedure to Install the Master Ground Cable on a BTS

Equipped with Optional Primary Surge Suppressor

Step

Action

Connect the Master Ground cable (cable Y) to the EARTH
GND connector on the Primary Surge Suppressor.

Connect the other end of cable Y to the customer–defined
master ground plate.

Summary of Contents for SC 300





























































































































































































Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands

Motorola SC 300, Manual

Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands