Motorola SC 300 Manual Download Page 136

Page: 136 / 188

Site I/O , Span Line, RGPS and Modem Cabling for Sites Equipped With
Customer–Supplied Site I/O Interface

– continued

PRELIMINARY

300 BTS Hardware Installation, ATP and FRU Procedures

DEC 2000

4-28

Table 4-25: Pin/Signal Information for Site I/O Cable

BTS Interface

Description

Wire/Stripe

Color

Yellow/Green

RX TIP Primary (Redundant)

Yellow/Blue

RX RING Primary (Redundant)

Yellow/Purple

TX TIP Primary (Redundant)

Span (Redundant)

Yellow/Grey

TX RING Primary (Redundant)

Span (Redundant)

Yellow/White

RX TIP Secondary (Redundant)

Green/Black

RX RING Secondary (Redundant)

Green/Brown

TX TIP Secondary (Redundant)

Green/Red

TX RING Secondary (Redundant)

Green/Orange

MODEM TIP

Green/Yellow

MODEM TIP

Phone (Modem)

Green/Blue

No connection

Phone (Modem)

Green/Purple

No connection

Green/Grey

MODEM RING

Green/White

MODEM RING

Connecting Customer–Defined
Inputs to the Site I/O Interface

The unit provides eight customer–defined inputs for connection to
external contacts. Each input (a signal/ground pair) is monitored for an
“OPEN” (>50 k Ohms) or “CLOSED” (<3 Ohms) condition.

Summary of Contents for SC 300





























































































































































































Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands

Motorola SC 300, Manual

Search results

Summary of Contents for SC 300

Reviews:

Related manuals for SC 300

Brands by name

Popular brands