manualshive.com logo in svg

Metos 4241001, Operating Instructions Manual, Page: 83 / 90

Share
Download
Metos 4241001 Operating Instructions Manual Download Page 83

 18

11 • OPERATING AT THE RATED HEAT OUTPUT

Checking the speed in the “MIN” position.
When the display shows the “MIN” speed

Press Fan to hold the “MIN” speed (the asterisk 
means that the speed is on hold).
Check the value displayed and then press Fan 
to check the speed in the “MAX” position.

Checking the speed in the “MAX” position.
When the display shows “MAX”

Check the value displayed.

NOTE: When the preset chamber temperature 
is reached (250 °C) the Burner Test is halted. 
To continue with the Test you will have 
to cool down the oven. Open the door and 
cool the oven with the door open until it stops 
automatically (at 50 °C).

Check the combustion, CO (ppm) and CO

2

 (%) 

values, with an appropriate instrument:

P r e s s   C L I M A   t o   e n a b l e   o p e n -
door operation (the door switch is 
bypassed and the CLIMA button lights 
up) and start the Chamber 1 burner.
Wait about 5 minutes.
Position the flue gas collection probe in the flue 
gas outlet pipe (chamber and boiler).

The CO

2

 must be for:

Natural gas 

between 9% and 10.5%

L.P.G.    

between 11% and 13%

 The CO must be no greater than 300  ppm 
(measured).
 Carry out the test in both convection and steam 
mode.
If these readings are outside the ranges, 
proceed as stated in the technical manual.
 For the conversion from natural gas to LPG, 
or vice versa, proceed as described in the 
technical manual.

Follow the same steps for the Chamber 2 
burner (if present).

- Boiler Burner
Select the Test for the boiler settings and follow 
the same procedure described above.

NOTE:  It is not necessary to enable open-door 
operation.

CLIMA

3

B r u 14 6

C h a m b e r   1
M i n   *

CLIMA

4

B r u 19 0

C h a m b e r   1
M a x

CLIMA

B R U

2

B o i l e r   1

900-----rev00

C o n v e r s i o n :   A s   m e n t i o n e d   a b o v e ,   e v e r y   a p p l i a n c e   i s   f a c t o r y   s e t   t o   b u r n   t h e   t y p e   o f   g a s 
specified, it may become necessary nonetheless to convert the appliance from one type of gas 
to another. Therefore, only personnel authorized by the company and belonging to the technical 
service who have the corresponding technical handbook can do this work.

CLIMA

Summary of Contents for 4241001



























































































Reviews:

No comments