manualshive.com logo in svg

Metos 4241001, Operating Instructions Manual, Page: 73 / 90

Share
Download
Metos 4241001 Operating Instructions Manual Download Page 73

 8

 

  Throughout installation it is vital to observe 

the following requirements:

4.1 • 

a n y   h e a l t h   a n d   h y g i e n e   s t a n d a r d s 
applicable to kitchens and eating places;

4.2 • 

local and/or territorial building regulations 
and fire prevention standards;

4.3 

•  current accident prevention guidelines;

4.4 • 

CEI requirements relating to electrical 
systems;

4.5 • 

UNI-CIG 8723 Standard “Gas systems for 
appliances used in professional kitchens 
and communal facilities”;

4.5 • 

the regulations of the gas supply company 
or agency;

4.7 • 

the regulations of the electrical power 
supply company or agency;

4.8 

•  any other local regulations.

4 • STATUTORY REQUIREMENTS, TECHNICAL REGULATIONS AND DIRECTIVES

900-----rev00

5.1 • 

To 

position the appliances, it is recommended 

to use the mount offered by the manufacturer; 
should you want to do things differently, it is 
necessary to take account of the weight of the 
appliance. 

5.2 • 

Before manoeuvring the oven into the 
selected position, attach the water inlet hoses 
and waste pipe to the relative connection 
points (refer to headings describing the water 
and drain connections).

5.3 • 

The distances from other appliances or from 
adjacent walls that must be left to allow 
access for servicing operations will be found 
on the installation diagram for the oven to 
connect. In the event of the oven being 
installed directly against an inflammable wall, 
suitable heat insulation must be provided. 

 

  Current fire regulations should be meticulously 

observed and respected. Do not obstruct 
the openings and slots in the casing as they 
disperse the heat in the electric component 
compartment. 

 

  Keep strictly to the installation diagrams.

5.4 • 

Once the appliance is installed, the electrical 
power cable must be protected, and never 
stretched or tugged.

5.5 • 

The appliance must be level: any difference 
in level or sloping of the supporting surface 
should be eliminated. Differences in level or 
sloping negatively affect oven operation. 

5 • POSITIONING

Summary of Contents for 4241001



























































































Reviews:

No comments