manualshive.com logo in svg

Metos 4241001, Operating Instructions Manual, Page: 69 / 90

Share
Download
Metos 4241001 Operating Instructions Manual Download Page 69

 4

1.1 • 

The oven must be installed, commissioned 
a n d   m a i n t a i n e d   o n l y   b y   a   L a i n o x 
authorized service agent.

1.2 • 

Carefully read the directions given in this 
manual; they contain important information 
on safety during installation, operation and 
maintenance.

 

  Keep this manual in a safe place for future 

consultation!

1.3 • 

This appliance must be put only to the 
use for which it is specifically intended, 
i.e. cooking foods; any other type of use is 
improper and therefore dangerous.

1.4 • 

Having removed the packing check that the 
appliance is not damaged in any way.

 

  If in doubt, proceed no further with installation 

of the appliance and contact the Lainox 
Customer Service or your dealer immediately.

1.5 • 

Packing materials are potentially dangerous 
and must not be left where children can 
play with them.

1.6 • 

Packing materials must be disposed of 
in conformity with local regulations. This 
normally means that the different materials 
are sorted according to type and collected as 
urban refuse.

1.7 • 

Before positioning and connecting the 
appliance, check that the utilities (electrical 
power, water and gas supplies) are as 
indicated on the data plate. 

 

  The data plate is on the right-hand side, at the 

bottom.

1.8 

•  Example of a data plate:

1.9 • 

T h e   p o s i t i o n s   o f   t h e   i n l e t   a n d   d r a i n 
connections are clearly labelled. For further 
details, see the installation diagram attached 
to this manual.

1.10 • 

In 

the event of breakdown or faulty operation, 

switch off the oven immediately!

1.11 • 

During installation and/or maintenance work 
it is recommended you wear gloves to protect 
your hands.

1.12 • 

Safety 

sticker

 

•  Maximum height for inserting containers with 

liquids.

1 •GENERAL REMINDERS

900-----rev00

0085

2008

EN 203/A1

AC  230V  50Hz

IT

IPX 5

G 25    /    m3/h

Qn   40   kW

Cat.

II 2H3+

NR   XXXXXXXXXX

kPa

200 - 500

P mbar

20; 28-30/37

TOT     1    kW

1 x 0.55  kW

G 20    /    m3/h

G 30   3.16  Kg/h

Pmax   /   mbar

Pmax   /   mbar

Pmin   /   mbar

Pmin   /   mbar

Pmin   /   mbar

A3

B13

B23

2008

3N AC  400V  50Hz

IPX 5

NR   XXXXXXXXXX

kPa
200 - 500

TOT     8    kW

1 x 0.25  kW

TYP. XXXXXXXX

TYP. XXXXXXXX

LOGO

LOGO

1600 mm (63 inch)

Summary of Contents for 4241001



























































































Reviews:

No comments