manualshive.com logo in svg

Metos 4241001, Operating Instructions Manual, Page: 38 / 90

Share
Download
Metos 4241001 Operating Instructions Manual Download Page 38

 38

900-----rev00

The main fault warning messages are:

MESSAGES

CHAMBER ERR - Message on the display 9. Oven 
temperature probe faulty, switch off the oven 
immediately and contact a  technician or authorized 
service agent.

NO WATER - This symbol lights up when there is no 
water reaching the appliance, in which case check 
that the shutoff valve is open and that there is water 
still coming from the main. If there is no supply from 
the main, inform the water company or agency. If there 
is no problem with the main, contact a technician or 
authorized service agent. In the meantime, the oven can 
still be used in convection mode, after pressing key 15 
to bypass the error signal.

MOTOR HIGH - The device preventing thermal 
overload of the motor has cut in. Switch off the oven 
immediately and contact a technician or authorized 
service agent.

CHAMBER HIGH - The oven safety thermostat has 
cut in. Switch off the oven immediately and contact a 
technician or authorized service agent.

Q U E N C H I N G   E R R O R   -   V a p o u r   c o n d e n s a t i o n 
temperature probe faulty. The condenser is in 
operation continuously, but the oven can still be used 
under close observation in convection and steam 
mode but not in combination mode (increased water 
consumption), until the arrival of a service technician.

HOT - An abnormally high temperature rise has 
registered in the compartment housing electrical 
components. The oven can still be used under close 
observation, until the arrival of a service technician.

TOO HOT - An excessive temperature rise registering 
in the electrical components compartment could result 
in damage to components. Switch off the oven 
immediately and contact a technician or authorized 
service agent.

24 • SELF-DIAGNOSIS AND FAULT IDENTIFICATION

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
C H A M B E R   E R R

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
N O   WAT E R

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
M O T O R   H I G H

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
C H A M B E R   H I G H

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
Q U E N C H I N G   E R R O R

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
H O T

CLIMA

2 5

2 5 0 2 ,3 4

M A N U A L
T O O   H O T

Summary of Contents for 4241001



























































































Reviews:

No comments