Medit i700, User Manual

Page: 18 / 224

16 User Manual
▪ Guidance 4
The i700 wireless system is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. Portable RF
communications equipment should be used no closer than 30 cm (12 inches) to any part of the i700 wireless system. Otherwise, degradation of
the performance of this equipment could result.
Guidance and Manufacturer’s Declaration – Electromagnetic Immunity
Immunity Test Band 1) Service 1) Modulation IEC 60601 Test Level Compliance Level
Proximity Fields
from RF Wireless
Communications
IEC 61000-4-3
380 – 390 MHz TETRA 400
Pulse
Modulation 18 Hz
27 V/m 27 V/m
430 – 470 MHz
GMRS 460;
FRS 460
FM ±5 kHz
Deviation
1 kHz sine
28 V/m 28 V/m
704 – 787 MHz LTE Band 13, 17
Pulse
Modulation 217 Hz
9 V/m 9 V/m
800 – 960 MHz
GSM 800:900;
TETRA 800;
iDEN 820;
CDMA 850;
LTE Band 5
Pulse
Modulation 18 Hz
28 V/m 28 V/m
1700 – 1990 MHz
GSM 1800;
CDMA 1900;
GSM 1900;
DECT;
LTE Band 1, 3, 4,
25;
UMTS
Pulse
Modulation 217 Hz
28 V/m 28 V/m
2400 – 2570 MHz
Bluetooth;
WLAN
802.11b/g/n;
RFID 2450;
LTE Band 7
Pulse
Modulation 217 Hz
28 V/m 28 V/m
5100 – 5800 MHz
WLAN
802.11a/n Pulse
Modulation 217 Hz
9 V/m 9 V/m
NOTE : These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects, and people.
WARNING
▪ Use of the i700 wireless adjacent to or on other equipment must be avoided as it may result in improper operation. If this use is necessary,
it is advisable that this and the other equipment be observed to verify that they are operating normally.
▪ The use of accessories, transducers, and cables other than those specified or provided by the Medit of the i700 wireless could result in high
electromagnetic emissions or reduced electromagnetic immunity from this equipment and result in improper operation.
1
For some services, only the uplink frequencies are included.
6. Wireless Compliance Information
6.1 FCC Compliance Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
▪ Reorient or relocate the receiving antenna.
▪ Increase the separation between the equipment and receiver.
▪ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
▪ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
FCC No.: 2A2QM-MD-IS0300
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
6.2 IC Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept