Lufft 8511.EAK Operating Manual Download Page 91

Page: 91 / 158

Manual

LCom

Page 91 of 158

Following column types are supported:

•

Date:

the date for the measurement (format as specified by date format

above)

•

Time:

the time for the measurement (format as specified by time format

above)

•

Date/Time:

date and time for the measurement (format as specified by date /

time format above)

•

Timestamp:

the UTC timestamp (seconds since 01.01.1970) for the

measurement

•

UMB Sensor Channel:

a measure value reported by the respective UMB

sensor channel (

any “value mapping” or scaling configured to the sensor

channel is processed)

•

NTCIP OID:

a measure value as reported for the NTCIP OID. Note: NTCIP

Uplink Protocol must be active, and the “NTCIP Sensor Assignment” must be

configured

•

Fixed String:

a fixed string.

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands