Lufft 8511.EAK Operating Manual Download Page 144

Page: 144 / 158

Manual

LCom

Page 144 of 158

Type

Description

Road Humidity (8 bit)

Road Condition (8 bit)

Precipitation Type (8 bit)

Unless adjusted by scaling or value mapping, the value reported by the UMB sensor

channel is used for all data types. If the UMB sensor channel does not already report

the proper TLS unit (e.g. for the old type 51), an appropriate scale factor and/or value

mapping must be configured for the UMB sensor channel.

6.1.2.2 Manufacturer defined data types FG3

Following manufacturer defined data types are supported:

Typ

Beschreibung

129

Ice Percentage (NIRS)

131

Waterfilm, height in 0.1mm (MicKS)

132

Road Condition (MicKS)

183

Prognosis Time until icing

184

Prognosis Road Temperature

185

Prognosis Road Condition

254

Boschung Alarm Status Code

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands