manualshive.com logo in svg

Lufft 8511.EAK, Operating Manual

Share
Download
Lufft 8511.EAK Operating Manual Download Page 67

ess.essNtcip.essNtcipTemperature.essWetbulbTemp.0 

.1.3.6.1.4.1.1206.4.2.5.2.5.3.0 

 

Wet Bulb 

Temperature (°C)  

- OR - 

Temperature (°C) 

Rel. Humidity (%) 

[Air Pressure (mBar)] 

ess.essNtcip.essNtcipTemperature.essDewpointTemp.0 

.1.3.6.1.4.1.1206.4.2.5.2.5.4.0 

 

Dewpoint 

Temperature (°C) 

ess.essNtcip.essNtcipTemperature.essMaxTemp.0 

.1.3.6.1.4.1.1206.4.2.5.2.5.5.0 

 

Temperature (“C) 

max 

ess.essNtcip.essNtcipTemperature.essMinTemp.0 

.1.3.6.1.4.1.1206.4.2.5.2.5.6.0 

 

Temperature (°C) 

min 

ess.essNtcip.essNtcipPrecip.essWaterDepth.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.1.0 

Deprecated 

Water Depth (cm) 

ess.essNtcip.essNtcipPrecip.essAdjacentSnowDepth.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.2.0 

 

Snow Depth (cm) 

ess.essNtcip.essNtcipPrecip.essRoadwaySnowDepth.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.3.0 

 

Snow Depth (cm) 

ess.essNtcip.essNtcipPrecip.essRoadwaySnowPackDepth.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.4.0 

 

Snow Depth (cm) 

ess.essNtcip.essNtcipPrecip.essPrecipYesNo.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.5.0 

 

Precipitation diff 

(mm) or Precipiation 

Intensity (mm/h) 

– 

compared to 

“Precipitation 

Yes/No Limit” 

ess.essNtcip.essNtcipPrecip.essPrecipSituation.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.6.0 

 

Precipitation Type 

(Lufft) or value 

mapped to NTCIP  

  

Precipitation 

Intensity (mm/h) 

ess.essNtcip.essNtcipPrecip.essIceThickness.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.7.0 

 

Ice Thickness (mm) 

ess.essNtcip.essNtcipPrecip.essPrecipitationStartTime.0 

.1.3.6.1.4.1.1206.4.2.5.2.6.8.0 

 

Precipitation diff 

(mm) or Precipiation 

Intensity (mm/h) 

– 

Summary of Contents for 8511.EAK































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands