Lufft 8511.EAK Operating Manual Download Page 15

Page: 15 / 158

Software Description

5.1 Installation

The following files must be copied to the \FFSDISK directory:

LCom.exe

– the LCom application

Text_de.uni

– the text modules for the user interface in German

Text_en.uni

– the text modules for the user interface in English

The following are also absolutely essential for NTCIP:

Snmpapi.dll

– the library for all SNMP functions

Snmp.dll

– the “master” SNMP agent (Microsoft)

Snmp_hostmib.dll

– the SNMP agent for “host” functions (Microsoft)

Snmp_mibii.dll

– the SNMP agent for “MIB-II” functions (Microsoft)

Ftpd.dll

– the FTP server (Microsoft)

SnmpNtcipAgent_Vx.x.dll

– the SNMP agent for NTCIP functions (Lufft)

The “Start.cmd” file must be copied to the \FFSDISK\Startup directory.

This command file copies

the “LCom.exe” file from the \FFSDISK directory to “\” (i.e.

to the RAM drive) and starts the application from there. This allows the file

“\FFSDISK\LCom.exe” to be overwritten by an update when necessary while the

system is running.

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands