Lufft 8511.EAK Operating Manual Download Page 118

Page: 118 / 158

Manual

LCom

Page 118 of 158

•

FPDIFF2:

Freezing Point Delta 2

•

WFHU1:

Waterfilm parameter 1

•

WFHU2:

Waterfilm parameter 2

•

WFHU3:

Waterfilm parameter 3

•

WFHU4:

Waterfilm parameter 4

•

DPDIFF:

Dewpoint Delta

•

PIMIN:

Precipitation Intensity minimum

5.13.10

Bridge Deck Alarm

The “Bridge Deck Alarm” model calculation has been developed to control a beacon

(using “Alarm Processing”, see 5.13.2) according to a customers specification.

The parameters are:

•

Air Temperature:

the air temperature sensor channel

•

Dewpoint Temperature:

the dewpoint sensor channel

•

Road Temperature:

the road/surface/bridge deck temperature channel

•

Freeze Point Temperature:

the freeze point temperature channel

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands