Lufft 8511.EAK Operating Manual Download Page 34

Page: 34 / 158

5.8.2 Configuration

The

“Ntcip” dialog on the LCom (or via the service program) is used to configure the

NTCIP protocol parameters. The input fields of this dialog are only enabled if

“Ntcip”

is selected

as the protocol in the “Uplink” dialog.

Note: The number of entries in the related tables, i.e. the number of sensors of

corresponding type that are available in the system, is set by configuring the

respective tables (windSensorTable, essTemperatureSensorTable etc.). Also, sensor

values can onl

y be assigned to previously configured table entries via “Sensor

Assignment”. So before assigning the actual UMB sensors to the respective NTCIP

OIDs, you need to set up the various “sensor tables” (to configure the number of wind

sensors, temperature sensors, pavement sensors etc.).

Note for TSS: TSS values are retrieved from a Wavetronix sensor via an UMB

Wavecon device. Data storage must be activated for these sensor channels in order

to transmit these sensor values via NTCIP-TSS.

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands