Lufft 8511.EAK Operating Manual Download Page 123

Page: 123 / 158

Manual

LCom

Page 123 of 158

5.13.12

Wavetronix Click 512

Here, parameters for transmitting events received from a Wavetronix Click 512 can

be configured. The events written by the Wavetronix device are collected (in the

original format) in a text file on the SD-card of the LCom, and transmitted in

configurable intervals to the server.

•

Is Active:

Wavetronix event transmission is active/inactive

•

Wavetronix Host/IP:

DNS Hostname or IP address of the RS232/Ethernet

interface which is connected to the Wavetronix output.

•

Wavetronix Port:

TCP port of the RS232/Ethernet interface which is

connected to the Wavetronix output.

•

FTP Transfer Interval:

Interval (in seconds) in which collected data is

transmitted to the server.

•

Remote Filename:

server filename

•

FTP Host/IP:

DNS name or IP address for the ftp server

•

FTP Port:

TCP port for the ftp server.

•

FTP User:

ftp user-id

•

FTP Password:

ftp password

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Related manuals for 8511.EAK

Brands by name

Popular brands