manualshive.com logo in svg

Lufft 8511.EAK, Operating Manual

Share
Download
Lufft 8511.EAK Operating Manual Download Page 116

Manual 

 

LCom 

 

 

 

 

Page 116 of 158  

 

Multiple instances for the model calculation can be configured (in case the station is 

equipped with more than one road sensor). 

 

Note: the default values are preset for the (German) TLS protocol, e.g. the “Dewpoint 

diff” value of 5.0 refers to 0.5 °C as the temperatures for TLS are in 1/10 °C. 

Please adjust the parameters as needed for the sensor channels configured here. 

 

•

  Active: this instance of the model calculation is active 

•

  Dewpoint Diff: the value that the road temperature must be below the dew 

point temperature for “slippery frosty” to be set (see above) 

•

 

Road Condition Dry: the road condition code for “dry” 

•

 

Slippery Frosty: the road condition code for “slippery frosty” 

•

  Road Condition: the road condition sensor channel 

•

  Road Temperature: the road temperature sensor channel 

•

  Water Film: the water film sensor channel 

•

  Dew point: the dew point sensor cannel  

 

 

Summary of Contents for 8511.EAK































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands