Lufft 8511.EAK Operating Manual Download Page 86

Page: 86 / 158

Manual

LCom

Page 86 of 158

•

NTP active:

Time synchronization via NTP is active

•

NTP server via GPRS:

The connection to the NTP server is established over

the GPRS modem (if this flag is selected, the connection to the NTP server is

only established after the GPRS connection has been established).

•

NTP server:

The DNS name or IP address of the NTP server.

•

NTP port:

The TCP/IP port (standard: 123) for the NTP server.

•

Sync interval:

The synchronization interval in seconds

•

Last sync:

Time of the last synchronization with the NTP server

•

Error:

Error on the last synchronization with the NTP server

– or “OK”

5.9.5 Station Status

The sensor channels for

•

Door contact

•

Power failure

and

•

Vent failure

can be

configured via “Station Status”:

Summary of Contents for 8511.EAK































































































































































Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands

Lufft 8511.EAK, Operating Manual

Search results

Summary of Contents for 8511.EAK

Reviews:

Brands by name

Popular brands